IAG Air Oil Separator - Street Series (Subaru)
The IAG Performance Street Series billet aluminum Air / Oil separator (AOS) vents crankcase gasses back to the turbo inlet. The design is based on years of service on racing and high horsepower Subaru's. The AOS's approximate 1-liter capacity, fully heated housing, superior breathing and unique patent pending baffle design sets it apart from the rest.
The IAG Performance Street Series billet aluminum Air/Oil separator (AOS) vents crankcase gasses back to the turbo inlet. The design is based on years of service on racing and high horsepower Subaru's. The AOS's approximate 1-liter capacity, fully heated housing, superior breathing and unique patent pending baffle design sets it apart from the rest.
- Breather Port Rotation For Install Ease
- Dual Breather Port
- Greater Pressure Stream Oil Separation
Notice the dual breather port? At first glance you might think this is excessive, however, our reasoning is grounded in simple physics. As air and particles of oil enter into the AOS, the largest particles of oil will collect on the inner surface of the can and drain to the bottom, but the smallest particles will remain suspended in the pressurized stream. As the air makes its way through the multi-stage baffle system, gravity pulls oil from the air. By increasing the overall volume of the breather opening on the top of the AOS, we have drastically decreased the exit velocity of the crankcase vent (CCV) stream. The slower velocity leads to greater oil separation from the pressure stream. A total of 9 mounting holes enables the breathing port a full 180° of rotation. On the bottom, a thick Viton o-ring seals the can. Every o-ring in our AOS is formed from Viton which offers superior temperature and chemical resistance.
- Large Billet Aluminum Design
- Approximate 1 Liter Holding Capacity
- Integrated 3 Port Billet Hose Barbs
- Aluminum Body is Powder Coated In Red, Black, Gold, Dark Silver. Also available in World Rally Blue (automotive paint)
The side of the AOS features 3 port billet hose barbs. There are NO plastic fittings that require thread tape to seal. The Subaru FA engine has 2 ports that vent crank pressure: two at the top of the block. Each engine vent port receives its own connection to the AOS. By giving each engine port its own entrance to the AOS we have allowed for more effective and faster excavation of crankcase pressure. Additionally, this reduces overall system pressure. With a 4" OD and 5.75" height, the AOS has an approximate 1 liter of holding capacity. The larger the AOS, the more power you can safely make without having to worry about the AOS overfilling.
- Unique Baffling Controls Crankcase Pressure
- Returns Oil To The Engine
- No Maintenance or Manual Draining Required
The bottom of the AOS is shaped like a snail, redirecting positive crank pressure into the same swirl pattern produced by the 3 side ports. Allowing maximum oil drainage while separating oil from the air in all the venting ports. Why not use a catch can? Unmodified Subaru's may require catch can draining as often as every few weeks. Heavily modified race cars may be as often as every race. Our AOS collects oil and actively drains the oil to the crankcase. The drain port is under the same crankcase pressure as the other ports that are on the side of the AOS. Under normal, off boost driving the weight of the collected oil will easily overcome the pressure in the drain line. However, under heavy boost (especially on higher powered engines) the crank pressure will push back up the drain with the same air/oil mixture that is seen on the side ports. The unique snail design allows the system to breath without disturbing the swirl pattern.
AOS Drain Port:
- The AOS drain port is able to be rotated for ease of installation.
- All fittings supplied with the AOS are anodized aluminum and feature Viton sealed ORB fittings.
- The supplied coolant hose is built to SAE 20R3 standards. It will withstand coolant temperatures of +257°F. The oil vapor hose is designed to withstand oil and fuel vapors, exceeding SAE J30R7 standards.
- Heated By Engine Coolant
- Reduces Moisture & Oil Mixing
The back plate of the AOS features a unique coolant routing system that heats the entire AOS to the same temperature of the engine. This maximizes the evaporation of any water collecting inside of the can. The hotter the AOS, the less water will collect inside and mix with the oil.
- Multi-point Adjustable Mounting Bracket
The center bracket allows for adjustable mounting. If your engine bay changes, you can easily change how and where you mount the AOS. A single laser-cut mounting bracket is included that fits nearly all applications and configurations. A laser cut harness relocation bracket is also included. The bracket allows the engine harness connector to be moved forward for additional clearance.
AOS in the Box:
- Ready To Install
- Hardware, Lines & Fittings Included
The AOS arrives completely assembled and ready for immediate installation. However, the entire unit can be broken down for cleaning. With a single allen wrench, you can remove 4 bolts and the AOS easily separates into individual pieces.
- 2015+ WRX
- 2014-2018 Forester XT
- 2008+ STI
- 2008-2014 WRX
- 2004-2007 STI
- 2006-2007 WRX
WARNING: Operating, servicing and maintaining a passenger vehicle or off-road vehicle can expose you to chemicals including engine exhaust, carbon monoxide, phthalates, and lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. To minimize exposure, avoid breathing exhaust, do not idle the engine except as necessary, service your vehicle in a well-ventilated area and wear gloves or wash your hands frequently when servicing your vehicle. For more information go to https://www.P65Warnings.ca.gov/passenger-vehicle.
Need Help with this product?
Chat with our staff using our Live Chat, Call us at 303.402.5142 or Email us email@example.com
Products ship within 2 days.
Friendly return policy because our priority is making sure you have the right product.